Test Spezifizéierung

Zweck

Gitt sécher datt d'Produkter vun der Firma de Client Ufuerderunge gerecht ginn, eng Basis fir d'Produktinspektioun ubidden an d'Produktqualitéit garantéieren.

Ëmfang vun der Uwendung

Dëse Standard gëlt fir all TFT Modul Produkter vun XX produzéiert.

Testen Ausrüstung

Elektresch Miessmaschinn, Testausrüstung, Lupp, Leuchtstofflampe, Vernier Caliper

Proufplang a préift Ëmweltbedingungen

D'Produktiounsunitéit (oder Prozess QC) féiert voll Inspektioun fir Erscheinungsinspektioun an elektresch Leeschtungstest, a fir Gréisstemessung oder speziell Inspektioun gëtt dat éischt Stéck vun all Modell 5st gepréift a getest.

D'Qualitéitsunitéit moosst 5Pcs fir déi éischt Prouf vun all Modell, an hëlt de GB / - 2012 normale Inspektioun eemoleg Proufplang fir d'Erscheinungsinspektioun un, an den allgemenge Kontrollniveau ass II.

Onqualifizéierten Niveau	Erlaabt Niveau （AQL）	Qualifizéiert Qualitéitsstandard Bewäertung
Haaptmangel		Wann d'Gréisst defekt ass, kritt 0 1 Retour
Ënnergewéinlech
total

Den Examinator muss en elektrostatesche Rank an aacht Fangerbett op béiden Hänn undoen. Wann et en LCD ass ouni Polarisator verbonnen, sollen all Fanger Fangerbett droen.

Den Examinator kann visuell iwwerpréiwen oder mat der Filmverglachstabell vergläichen.

W.e.g. bezitt Iech op d'Prouf fir den elektreschen Test mat Testanlag a Displaybildschierm.

D'Distanz tëscht den Ae vum Inspekter an dem Produkt ass 30 ~ 40 cm. Den Iwwerbléckwénkel vun der Inspektioun ass ± 15 Grad op der viischter Uewerfläch vum vertikalen Affichage Panel an ± 45 Grad op der Front Uewerfläch vum horizontalen Display Panel (kuckt d'Figur ënnen)

Ëmfeld Beliichtung: 800 ～ 1200LUX fir visuell Inspektioun

Ëmwelt Temperatur: 25 ± 5 ℃

Fiichtegkeet: 25 ~ 75% RH

Check Artikel

(1) Definitioun vu Punktdefekte verursaacht duerch intern Paneele.

a) Hell Flecken: hell, konstant Gréisst Punkten erschéngen um LCD ënner dem schwaarze Muster.

b) Däischter Punkte: An de reng rouden, gréngen a bloe Biller erschéngen däischter Punkte mat der selwechter Gréisst um LCD.

c) 2 Nopeschpunkte = 1 Pair = 2 Punkte.

Show Scheck

Artikel	Beschreiwung	Akzeptabel Quantitéit	MAJ	MIN
Highlights	zoufälleg	N≤3		√
	Zwee bascht Punkten	N≤0
	Zwee bascht Punkten	N≤0
Distanz	Minimum Distanz tëscht zwee hell Flecken	5mm
donkel Fleck	zoufälleg	N≤4		√
	Zwee bascht Punkten	N≤0
	Zwee bascht Punkten	N≤0
Total vun donkelen Flecken an helle Flecken		N≤6		√
Distanz	Minimum Distanz tëscht zwee hell Flecken (donkel Flecken)	5mm		√
Kleng Highlights		D≤can be ignored，<D≤, N≤4,spacing≧5mmD（Point diameter）		√
Show fault	V/H line/line crossover line etc.	Not allowed	√
Chromatic aberration, uneven; ripple; hot spot	Pass 5% filter under 50% dark light	Invisible, can be judged by limit sample if necessary		√

*Note: Defects on the black matrix (outside the active area) are not considered defects

Visual inspection

Artikel	Beschreiwung	Akzeptabel Quantitéit	MAJ	MIN
Point defect (display and appearance)	Black spots, white spots, bright spots	D≤ignorable, <D≤, N≤4, spacing ≥5mm (Figure 2)		√
Bad linearity (display and appearance)	Black line, white line, bright line	W≤ignorable, <W≤,L≤, N≤4,		√
Polarizer defect	Dents, bubbles	D≤ignorable, <D≤, N≤4,		√
Polarizer defect	Scratch	W≤ignorable,<W≤,L≤, N≤4		√
Panel crack		Not allowed	√
Damaged TFT non-lead side		The distance between the minimum break point area, d1≧, cannot be ignored; d1<, N≦0d 1: the minimum distance between the break point area and the dot area		√
Damaged TFT pin side		The alignment mark is damaged, the damaged angle>90	√
		W≦,L is ignored, but the pin cannot be damaged
		W≦, (D depth)≦1/2 (1 layer glass thickness)
Damaged TFT lead side corner		The swastika cannot be damaged. W≦,L≦5mm		√
TFT / CF edge burr		d2≦d 2: The distance between the burr and the edge of the TFT		√
other	Poor sealing glue	Height: no more than length: no more than 80mm, the sealing glue must completely cover the crystal filling mouth and the penetration depth is greater than		√
	LCD dimensions	The size refers to the design specification, the tolerance is ± mm, if it exceeds the tolerance range, it is unqualified	√
	The liquid crystal is not completely poured into the box	Not allowed	√
	Gas enters the box during crystal filling	Not allowed	√
	Smudge	Stain that cannot be wiped off is not allowed to have liquid crystal on the surface or in the glass gap		√
Module appearance	Newton ring	There are Newton rings and interference lines on the touch screen, rejected		√
		The pattern font is clear, the font line becomes thicker or thinner than the normal line width ≤1/3 (and ≤+/), no hyphenation. accept		√
	Drums on the touch screen	Acceptable without affecting writing		√
	There are fish-eye bubbles on the surface of the touch screen FILM	According to the inspection standard of the touch screen		√
Poor assembly	Module assembly does not match the assembly instructions	Reject	√
Poor assembly	The assembly does not meet the process requirements (fixed double-sided tape or shading tape is not attached, etc.)	Reject	√
Poor assembly	The connection between the components is not strong (the glass is separated from the backlight, etc.)	Reject	√
Defects when attaching transfer paper	Insufficient adhesion to tear off the protective film	Reject		√
	Attach position	Does not meet the specifications, rejected		√
	Attaching angle	Attached to the edge of the LCD edge angle is greater than ±15 degrees, rejected		√
Poor coding		Does not meet the document requirements	√
Other items	PCBA, HSC, FPC, backlight, etc.	Refer to "LCM Finished Product Inspection Specification" ~ conduct inspection

Remarks:

1. Ignore any defects on the protective film of the polarizer, such as scratches, bubbles and particles on the protective film.

2. The angle of all damage must be greater than 90 degrees as shown on the right.

3. If the customer has specified requirements according to customer requirements.